"$activateStimEL" 修訂間的差異

出自 DDCC TCAD TOOL Manual
前往: 導覽搜尋
行 12: 行 12:
 
$activateStimEL
 
$activateStimEL
 
Method QW_number 1st_QW_layerNum 2nd_QW_layerNum 3rd_QW_layerNum ...
 
Method QW_number 1st_QW_layerNum 2nd_QW_layerNum 3rd_QW_layerNum ...
<math> \beta_{1} R_{th,1} </math> , P3_1, P4_1
+
<math> \beta_{1}~~ R_{th,1} ~~ P3_1~~ P4_1</math>
<math> \beta_{2} R_{th,2} </math> , P3_2, P4_2
+
<math> \beta_{2}~~ R_{th,2} ~~ P3_2~~ P4_2</math>
<math> \beta_{3} R_{th,3} </math> , P3_3, P4_3
+
<math> \beta_{3}~~ R_{th,3} ~~ P3_3~~ P4_3</math>
<math> \beta_{4} R_{th,4} </math> , P3_4, P4_4
+
<math> \beta_{4}~~ R_{th,4} ~~ P3_4~~ P4_4</math>
<math> \beta_{5} R_{th,5} </math> , P3_5, P4_5
+
<math> \beta_{5}~~ R_{th,5} ~~ P3_5~~ P4_5</math>
 
.....
 
.....
 
..... total N layers (regions)
 
..... total N layers (regions)
<math> \beta_{N} R_{th,N} </math> , P3_N, P4_N
+
<math> \beta_{N}~~ R_{th,N} ~~ P3_N~~ P4_N </math>
   
 
Method: 1 -> Given <math> \beta and R_{th} </math> of each layer. If this is layer is not QW, set <math> \beta=0.0~~,and~~R_{th}=0.0 </math>
 
Method: 1 -> Given <math> \beta and R_{th} </math> of each layer. If this is layer is not QW, set <math> \beta=0.0~~,and~~R_{th}=0.0 </math>

於 2019年9月29日 (日) 21:39 的修訂

$activateStimEL is a command used to enable the calculation of stimulate Emission.

The stimulate emission coefficient is calculated by:

B_{stim} = B_{0} \times \beta \times \frac{R_{rad}}{R_{th}-R_{rad}}
R_{stim} = B_{stim} \times n \times p 
 B_{0}:  is the radiative recombination coefficient
 R_{th}: is the threshold recombination rate
 R_{rad}:  is the spontaneous radiative recombination rates decided by   B_{0}\times n \times p 
 \beta:  is the fitting coefficient. 

The way to activate the command is as following

$activateStimEL
Method QW_number 1st_QW_layerNum 2nd_QW_layerNum 3rd_QW_layerNum ...
 \beta_{1}~~  R_{th,1}  ~~ P3_1~~ P4_1
 \beta_{2}~~  R_{th,2}  ~~ P3_2~~ P4_2
 \beta_{3}~~  R_{th,3}  ~~ P3_3~~ P4_3
 \beta_{4}~~  R_{th,4}  ~~ P3_4~~ P4_4
 \beta_{5}~~  R_{th,5}  ~~ P3_5~~ P4_5
.....
..... total N layers (regions)
 \beta_{N}~~  R_{th,N}  ~~ P3_N~~ P4_N 
Method: 1 -> Given  \beta and R_{th}  of each layer. If this is layer is not QW, set  \beta=0.0~~,and~~R_{th}=0.0 
Method: 2 -> defined for future expansion
P3, P4 : Not used, may be used when Method 2 is activate in the future


For example:

$activateStimEL
1 1 2 
0.000 5.0e27 0.00 0.00
1.000d-4 5.0e27 0.00 0.00
0.000 5.0e27 0.00 0.00
0.000 5.0e27 0.00 0.00

In this command, use method 1. There is 1 QW which is the 2nd layer. The  \beta and  R_{th} of the 2nd layer is 1.0e-4 and 5.0e27  (1/cm^{3}s)