「$ranges」：修訂間差異
無編輯摘要 |
小無編輯摘要 |
||
| （未顯示同一使用者於中間所作的 9 次修訂） | |||
| 第3行： | 第3行： | ||
$ranges | $ranges | ||
x_left x_right y_top y_bottom | x_left x_right y_top y_bottom | ||
... | |||
... | |||
repeat for N ranges defined by [[$totalregion]] | repeat for N ranges defined by [[$totalregion]] | ||
| 第8行： | 第10行： | ||
'''<big><big>Example:</big></big>''' | '''<big><big>Example:</big></big>''' | ||
$ranges | $ranges | ||
-0.1 10.0 20.0 15.0 | |||
-0.1 10.0 15.0 0.0 | |||
... | |||
This means that there are two rectangular regions. | This means that there are two rectangular regions. The first region covers the area which x starts from -0.1 um to 10.0 um and y starts from 15.0 um to 20.0 um. | ||
The second region covers the area which x starts from -0.1 um to 10.0 um and y starts from 0.0 um to 15.0 um. | The second region covers the area which x starts from -0.1 um to 10.0 um and y starts from 0.0 um to 15.0 um. | ||
<br>'''<big><big>The $ranges setting in GUI interface is here</big></big>''' <br> | <br>'''<big><big>The $ranges setting in GUI interface is here</big></big>''' <br> | ||
1. Press Set up the width of project<br> | 1. Press '''Set up the width of project'''.<br> | ||
2. Please set up the initial width of your general structure | 2. Please set up the initial width of your general structure.<br> | ||
[[檔案:2D_ranges_fig1.jpg|1200px]] | |||
[[檔案: | |||
3. Press '''Add new epitaxial ranges'''.<br> | |||
4. Set up the thickness of your structure.<br> | |||
5. Press '''Apply'''.<br> | |||
[[檔案:2D_ranges_fig2.jpg|1200px]] | |||
6. Get the first region!<br> | |||
[[檔案:2D_ranges_fig3.jpg|1200px]] | |||
Related commands:<br> | <br>Related commands:<br> | ||
[[$totalregion]], [[$parameters]] | [[$totalregion]], [[$parameters]] | ||
於 2024年8月21日 (三) 16:45 的最新修訂
This is to set up the range of the rectangular regions. There are four columns for each region to fill in x start point left x end point right y start point top y end point bottom.
$ranges x_left x_right y_top y_bottom ... ... repeat for N ranges defined by $totalregion
Example:
$ranges -0.1 10.0 20.0 15.0 -0.1 10.0 15.0 0.0
This means that there are two rectangular regions. The first region covers the area which x starts from -0.1 um to 10.0 um and y starts from 15.0 um to 20.0 um. The second region covers the area which x starts from -0.1 um to 10.0 um and y starts from 0.0 um to 15.0 um.
The $ranges setting in GUI interface is here
1. Press Set up the width of project.
2. Please set up the initial width of your general structure.
3. Press Add new epitaxial ranges.
4. Set up the thickness of your structure.
5. Press Apply.
6. Get the first region!
Related commands:
$totalregion, $parameters