"$usemubydopeT" 修訂間的差異
出自 DDCC TCAD TOOL Manual
| (未顯示由 2 位使用者於中間所作的 2 次修訂) | |||
| 行 14： | 行 14： | ||
Type |
Type |
||
0: Use the original mobility defined in parameter setions |
0: Use the original mobility defined in parameter setions |
||
| − | 1: <math> \mu_{n} = p1 \times (\frac{T}{p3}) ^{p2} </math> , and <math> \mu_{p} = p4 \times (\frac{T}{p6}) ^{p5} </math> |
+ | 1: <math> \mu_{n} = p1 \times \left(\frac{T}{p3}\right) ^{p2} </math> , and <math> \mu_{p} = p4 \times \left(\frac{T}{p6}\right) ^{p5} </math> |
2: <math> \mu_{n} = p1 + \left(\frac{P2-P1}{1+(\frac{N_{d}}{p3}) ^{p4}} \right) </math> , and <math> \mu_{p} = p5 + \left(\frac{P6-P5}{1+(\frac{N_{a}}{p7}) ^{p8}} \right) </math> |
2: <math> \mu_{n} = p1 + \left(\frac{P2-P1}{1+(\frac{N_{d}}{p3}) ^{p4}} \right) </math> , and <math> \mu_{p} = p5 + \left(\frac{P6-P5}{1+(\frac{N_{a}}{p7}) ^{p8}} \right) </math> |
||
3: <math> \mu_{n,0} = p1 + \left(\frac{P2-P1}{1+(\frac{N_{d}}{p3}) ^{p4}} \right) </math>, <math>\mu_{n} = \mu_{n,0} \times \left(\frac{T}{p5}\right) ^{p6} </math> , and |
3: <math> \mu_{n,0} = p1 + \left(\frac{P2-P1}{1+(\frac{N_{d}}{p3}) ^{p4}} \right) </math>, <math>\mu_{n} = \mu_{n,0} \times \left(\frac{T}{p5}\right) ^{p6} </math> , and |
||
| 行 24： | 行 24： | ||
31: <math> \mu_{n,0} = p1 + \left(\frac{P2-P1}{1+(\frac{N_{d}^{+}}{p3}) ^{p4}} \right) </math>, <math>\mu_{n} = \mu_{n,0} \times \left(\frac{T}{p5}\right) ^{p6} </math> , and |
31: <math> \mu_{n,0} = p1 + \left(\frac{P2-P1}{1+(\frac{N_{d}^{+}}{p3}) ^{p4}} \right) </math>, <math>\mu_{n} = \mu_{n,0} \times \left(\frac{T}{p5}\right) ^{p6} </math> , and |
||
<math> \mu_{p,0} = p7 + \left(\frac{P8-P7}{1+(\frac{N_{a}^{-}}{p9}) ^{p10}} \right) </math>, <math>\mu_{p} = \mu_{p,0} \times \left(\frac{T}{p11}\right) ^{p12} </math>. |
<math> \mu_{p,0} = p7 + \left(\frac{P8-P7}{1+(\frac{N_{a}^{-}}{p9}) ^{p10}} \right) </math>, <math>\mu_{p} = \mu_{p,0} \times \left(\frac{T}{p11}\right) ^{p12} </math>. |
||
| + | |||
| + | |||
| + | <br>'''<big><big>The $usemubydopeT setting in GUI interface is here</big></big>''' <br> |
||
| + | Press '''Thermal''', check the box and set the fields as needed!<br> |
||
| + | [[檔案:2D_usemubydopeT_fig1.jpg|1200px]] |
||
於 2024年11月21日 (四) 17:44 的最新修訂
$usemubydopeT is to enable the temperature and carrier density dependent mobility module with the predefined function. The function is designed for each region. So if total n regions is used, then you will need to setup n regions. The format is
$usemubydopeT Type_R1 p1 p2 p3 p4 p5.....p12 Type_R2 p1 p2 p3 p4 p5.....p12 Type_R3 p1 p2 p3 p4 p5.....p12 ... ... ... Type_RN p1 p2 p3 p4 .....p12
Type
0: Use the original mobility defined in parameter setions 1:, and
2:
, and
3:
,
, and
,
.
If the mobility is for activated dopant density then
21:, and
31:
,
,
The $usemubydopeT setting in GUI interface is here
Press Thermal, check the box and set the fields as needed!
