"$negfoverlapcalculation" 修訂間的差異
(已建立頁面，內容為 "$negfoverlapcalculation is the command to setup the region of surface roughness. The first term is to setup what kind of structure, 1 is circle, and 2 is rectangular...") |
|||
| (未顯示同一使用者於中間所作的 4 次修訂) | |||
| 行 1： | 行 1： | ||
| − | $negfoverlapcalculation is the command to setup the region of surface roughness. The first term is to setup what kind of structure, 1 is circle, and 2 is rectangular for cross section region. If the first term is 1, then the four parameters after that are fix factor for surface roughness scattering, root mean square height<math>\Delta</math>of surface roughness, diameter of the outer circle, and the diameter of the inner circle. If the first term is 2, then the four parameters after that are fix factor for surface roughness scattering, root mean square height<math>\Delta</math>of surface roughness, width, and height.<br> |
+ | $negfoverlapcalculation is the command to setup the region of surface roughness. You can also use this function and set the parameter with our GUI version at the input box of "Overlap Calculation" in GUI. The first term is to setup what kind of structure, 1 is circle, and 2 is rectangular for cross section region. If the first term is 1, then the four parameters after that are fix factor for surface roughness scattering, root mean square height<math>\Delta</math>of surface roughness, diameter of the outer circle, and the diameter of the inner circle. If the first term is 2, then the four parameters after that are fix factor for surface roughness scattering, root mean square height<math>\Delta</math>of surface roughness, width, and height.<br> |
| + | |||
| + | $negfoverlapcalculation |
||
| + | cross section geometry # 1: circle, 2: rectangular |
||
| + | calibration rms diameter(with oxide) diameter(without oxide) [unit: cm] # for circle |
||
| + | calibration rms width height [unit: cm] # for rectangular |
||
| + | load-overlap-start load-overlap-end |
||
| + | |||
Example: |
Example: |
||
$negfoverlapcalculation |
$negfoverlapcalculation |
||
| 行 5： | 行 5： | ||
1.0e-3 1.0e-7 20.0e-7 16.0e-7 |
1.0e-3 1.0e-7 20.0e-7 16.0e-7 |
||
387 396 |
387 396 |
||
| − | # Note: 1 --> circle, 2 --> rectangular |
||
| + | |||
| − | # sfix rms_h t_diameter in_diameter (unit: cm) for circle |
||
| ⚫ | |||
| − | # sfix rms_h width height (unit: cm) for rectangular |
||
| + | related commands: |
||
| − | # loadoverlapstart loadoverlapend |
||
| + | [[$ifsolvenegf]], [[$negfifscattering]], [[$negfsurfaceroughness]] |
||
| ⚫ | |||
於 2019年6月18日 (二) 01:13 的最新修訂
$negfoverlapcalculation is the command to setup the region of surface roughness. You can also use this function and set the parameter with our GUI version at the input box of "Overlap Calculation" in GUI. The first term is to setup what kind of structure, 1 is circle, and 2 is rectangular for cross section region. If the first term is 1, then the four parameters after that are fix factor for surface roughness scattering, root mean square height
of surface roughness, diameter of the outer circle, and the diameter of the inner circle. If the first term is 2, then the four parameters after that are fix factor for surface roughness scattering, root mean square heightof surface roughness, width, and height.
$negfoverlapcalculation cross section geometry # 1: circle, 2: rectangular calibration rms diameter(with oxide) diameter(without oxide) [unit: cm] # for circle calibration rms width height [unit: cm] # for rectangular load-overlap-start load-overlap-end
Example:
$negfoverlapcalculation 1 1.0e-3 1.0e-7 20.0e-7 16.0e-7 387 396
The last two parameters is what region of overlap. For example in this case we have 681 mesh grids from drain(left) to source(right), and the position of channel is from 300 to 400, then 387 to 396 is in the channel near the source what region of overlap we choose.
related commands:
$ifsolvenegf, $negfifscattering, $negfsurfaceroughness
