「$SourceFrequency」:修訂間差異

出自DDCC TCAD TOOL Manual
跳至導覽 跳至搜尋
Mike留言 | 貢獻
已建立頁面,內容為 "= Not finish = =='''Format'''== $SourceFrequency ''fp1 fp2'' <font color=green>// where ''fp1-2'' are floating points.</font> <font size=3> Sou..."
 
Mike留言 | 貢獻
無編輯摘要
 
(未顯示同一使用者於中間所作的 5 次修訂)
第1行: 第1行:
= Not finish =
=='''Format'''==
=='''Format'''==
  $SourceFrequency
  $SourceFrequency
   ''fp1   fp2''                <font color=green>// where ''fp1-2'' are floating points.</font>
   ''freq   range    f<sub>σ</sub>    f<sub>t0</sub>''                <font color=green>// all are floating points.</font>


<font size=3>
<font size=3>
Source%dir, Source%posi.
Source%freq, Source%range, Source%fac_sig, Source%fac_t0
</font>
</font>
  When the units digit of type in [[$SourceType]] is
  1: only ''freq'' works, which represents what the frequency is.
  2: ''range    f<sub>σ</sub>    f<sub>t0</sub>''
  3: ''freq    range    f<sub>σ</sub>    f<sub>t0</sub>''
  4: ''freq    ????''
''range'' means what the bandwidth you want to simulate. <br>
''f<sub>σ</sub>'' means the edge of bandwidth is located at ''f<sub>σ</sub>''th of Gaussian sigma (σ). <br>
''f<sub>t0</sub>'' means the source starts at ''f<sub>t0</sub>'' times σ. <br>


=='''Example'''==
=='''Example'''==
  $SourceFrequency
  $SourceFrequency
   1.5e15 1e13
   1e15    0.5e15   3    5
 
This means the program has 2 objects in the simulation.


This means the center of frequency is 1e15 Hz, 1.5e15 and 0.5e15 are at 3σ of Gaussian distribution, and the source will starts when the time is over 5σ.


== '''Related commands''' ==
== '''Related commands''' ==
: [[$SourceType]], [[$SourcePosition]]
: [[$SourceType]], [[$SourceAmp]], [[$SourcePosition]], [[$SourceFrequency]]

於 2021年2月25日 (四) 05:37 的最新修訂

Format

$SourceFrequency
 freq    range    fσ    ft0                // all are floating points.

Source%freq, Source%range, Source%fac_sig, Source%fac_t0

 When the units digit of type in $SourceType is
 1: only freq works, which represents what the frequency is.
 2: range    fσ    ft0
 3: freq    range    fσ    ft0
 4: freq    ????

range means what the bandwidth you want to simulate.
fσ means the edge of bandwidth is located at fσth of Gaussian sigma (σ).
ft0 means the source starts at ft0 times σ.

Example

$SourceFrequency
 1e15    0.5e15    3    5

This means the center of frequency is 1e15 Hz, 1.5e15 and 0.5e15 are at 3σ of Gaussian distribution, and the source will starts when the time is over 5σ.

Related commands

$SourceType, $SourceAmp, $SourcePosition, $SourceFrequency