「$negfoverlapcalculation」：修訂間差異
小無編輯摘要 |
無編輯摘要 |
||
| 第1行： | 第1行： | ||
$negfoverlapcalculation is the command to setup the region of surface roughness. The first term is to setup what kind of structure, 1 is circle, and 2 is rectangular for cross section region. If the first term is 1, then the four parameters after that are fix factor for surface roughness scattering, root mean square height<math>\Delta</math>of surface roughness, diameter of the outer circle, and the diameter of the inner circle. If the first term is 2, then the four parameters after that are fix factor for surface roughness scattering, root mean square height<math>\Delta</math>of surface roughness, width, and height.<br> | $negfoverlapcalculation is the command to setup the region of surface roughness. The first term is to setup what kind of structure, 1 is circle, and 2 is rectangular for cross section region. If the first term is 1, then the four parameters after that are fix factor for surface roughness scattering, root mean square height<math>\Delta</math>of surface roughness, diameter of the outer circle, and the diameter of the inner circle. If the first term is 2, then the four parameters after that are fix factor for surface roughness scattering, root mean square height<math>\Delta</math>of surface roughness, width, and height.<br> | ||
$negfoverlapcalculation | |||
cross section geometry # 1: circle, 2: rectangular | |||
calibration rms diameter(with oxide) diameter(without oxide) [unit: cm] # for circle | |||
calibration rms width height [unit: cm] # for rectangular | |||
load-overlap-start load-overlap-end | |||
Example: | Example: | ||
$negfoverlapcalculation | $negfoverlapcalculation | ||
| 第6行： | 第13行： | ||
387 396 | 387 396 | ||
The last two parameters is what region of overlap. For example in this case we have 681 mesh grids from drain(left) to source(right), and the position of channel is from 300 to 400, then 387 to 396 is in the channel near the source what region of overlap we choose.<br> | The last two parameters is what region of overlap. For example in this case we have 681 mesh grids from drain(left) to source(right), and the position of channel is from 300 to 400, then 387 to 396 is in the channel near the source what region of overlap we choose.<br> | ||
related commands: | related commands: | ||
[[$ifsolvenegf]], [[$negfifscattering]], [[$negfsurfaceroughness]] | [[$ifsolvenegf]], [[$negfifscattering]], [[$negfsurfaceroughness]] | ||
於 2018年7月30日 (一) 01:22 的修訂
$negfoverlapcalculation is the command to setup the region of surface roughness. The first term is to setup what kind of structure, 1 is circle, and 2 is rectangular for cross section region. If the first term is 1, then the four parameters after that are fix factor for surface roughness scattering, root mean square heightof surface roughness, diameter of the outer circle, and the diameter of the inner circle. If the first term is 2, then the four parameters after that are fix factor for surface roughness scattering, root mean square heightof surface roughness, width, and height.
$negfoverlapcalculation cross section geometry # 1: circle, 2: rectangular calibration rms diameter(with oxide) diameter(without oxide) [unit: cm] # for circle calibration rms width height [unit: cm] # for rectangular load-overlap-start load-overlap-end
Example:
$negfoverlapcalculation 1 1.0e-3 1.0e-7 20.0e-7 16.0e-7 387 396
The last two parameters is what region of overlap. For example in this case we have 681 mesh grids from drain(left) to source(right), and the position of channel is from 300 to 400, then 387 to 396 is in the channel near the source what region of overlap we choose.
related commands:
$ifsolvenegf, $negfifscattering, $negfsurfaceroughness