"$triregionnumber" 修訂間的差異
| (未顯示由 1 位使用者於中間所作的 4 次修訂) | |||
| 行 2： | 行 2： | ||
<big><big>'''Example'''</big></big> |
<big><big>'''Example'''</big></big> |
||
| − | |||
| − | [[檔案:IMAG0233.jpg|700px|left]] |
||
$triregionnumber |
$triregionnumber |
||
| 行 68： | 行 66： | ||
<math>f_4<y<f_5</math> |
<math>f_4<y<f_5</math> |
||
| − | [[檔案:pic2.png|700px |
+ | [[檔案:pic2.png|700px]] |
| + | |||
| + | |||
| + | |||
| + | <br>'''<big><big>The $triregionnumber setting in GUI interface is here</big></big>''' <br> |
||
| + | 1. After completing the processes for [[$triregiontype]], here shows the number of regions!<br> |
||
| + | [[檔案:2D_triregionnumber_fig1.jpg|1200px]] |
||
| + | |||
| − | <br> |
||
| − | [[$emptyperiodshape]], |
+ | <br><br>[[$emptyperiodshape]], |
於 2025年1月6日 (一) 17:32 的最新修訂
The number of regions that is in the triangular shape.
Example
$triregionnumber 2
This means that there are two triangular regions. This command must be set after the command
$ranges. The "triregionnumber" must be smaller than the "range number".
This command needs to be set before the command before the commands $triregiontype, $triranges,
For example:
$triregionnumber 2
$triregiontype @type @periodnumber @period_spacing @type @periodnumber @period_spacing
$triranges @f1 @f2 @f3 @f4 @f5 @f6 @f1 @f2 @f3 @f4 @f5 @f6
@f1 @f2 @f3 @f4 @f5 @f6 are defined below according to its type For the @type, it is the same definition as type in $emptyperiodshape, see below For @periodnumber, it is repeating how many times For the @period_spacing, it is defining the spacing of each repeating objects.
Example of @type
@type.1~4 are triangle, circle, ellipse and rectangle.
@type = 1 is triangle. If it have n-trianges, it it repeating along x direction.
@type = 11 is triangle. If it have n-trianges, it it repeating along y direction.
@type = 2 is circle. If it have n-circles, it it repeating along x direction.
@type = 21 is circle. If it have n-circles, it it repeating along y direction.
@type = 3 is ellipse. If it have n-ellipses, it it repeating along x direction.
@type = 31 is ellipse. If it have n-ellipses, it it repeating along y direction.
@type = 4 is rectangle. If it have n-rectangle, it it repeating along x direction.
@type = 41 is rectangle. If it have n-rectangle, it it repeating along y direction.
If the parameters are not show in the figure, you should set those parameters as 0.
Type5~8 are sine shape period structure.
Type.5 and 6 can be determined by this expression:
Type.7 and 8 can be determined by this expression:
The $triregionnumber setting in GUI interface is here
1. After completing the processes for $triregiontype, here shows the number of regions!
